Pretty much every one of the shoppers invest in the lamps might be consulting the set up, often anxious about irrespective of whether the package installation, should the service there is no method to install the tips on how to do, the usually employed lamps and lanterns are crystal lamp, crystal pendant, fluorescent light fixture, marble lamps, we’re devoted towards the to in accordance on the distinctive sorts of house lighting set up, chandeliers, ceiling lamps, wall lamps, has its very own installation strategy to everybody as under:
(A) set up specifications:
one lamps and accessories need to be finish, there ought to be no mechanical harm, deformation, paint peeling and lamp cover rupture together with other defects

two the load carrying capability in the fixed element of the wall mounted ceiling mounted light fixture shall be matched with all the excess weight of the lamp

three the lamp must be equipped with hanging line box, every single hanging line box can only be set up a set of pendant lamp. The surface with the pendant lamp need to be well insulated, and there may not be a joint, as well as the wire cross segment shall not be significantly less than 0.4 mm. Inside the wiring box hanging line really should be taken to prevent thrum stress the lamp drop measures. Weighed greater than a kilogram of lamps should really be arranged chain. When the chandelier lamp weight more than 3 kg, must utilize the embedded hook or even a bolt fixed. The chain lamp line should not be subject to tension, and also the lamp wire need to be compiled with fork chain

4 the incandescent lamp since the light supply of ceiling lamp can not be put in directly around the flammable element; lighting shall be close to the lampshade; when the lighting and insulation amongst the distance much less than five mm, lighting and insulation amongst Taiwan need to take heat insulation measures. The electrical power of an incandescent lamp shall not exceed the maximum energy permitted from the lamp.

five fluorescent lamp since the light source, ballast must be installed within the phase, the lamp should really stop lamp foot off shell and remain during the lamp box inner margin, giant lights and also the frame with the roof decorative lines are parallel, the lamp frame need to be close to the roof surface

six Light socket need to be grounded in the center speak to terminals, zero line should really be grounded within the thread in the terminal, lamp holder from the insulated shell need to be full, no damage and leakage phenomenon

seven fixed lantern hook, its diameter should not be less than the diameter with the lamp as well as lamp hanger, a minimum of not less than 6 mm

(B) set up approach of various lamps:

one: the chandelier put in inside the top surface on the concrete, the embedded parts, bolts and bolt penetrating tube growth. When installing the theme and the weight from the noticeable light to determine the tube expanding bolt specifications, however the minimal should not be much less than M6 (mm), bull droplight shouldn’t be significantly less than M8 (mm), the quantity of bolts not less than much less two pieces. Light self tapping screws for expanding tubes can not be used

2 ceiling lamp includes a circular, square or rectangular base (chassis), base dimension array. The base from the lamp can bolt growth pipe, can also use wood screws in embedded block fastening. If your holder base diameter more than a hundred mm, need to use the two screws. If the base of your lamp is set up, the bolt diameter shall not be less than six mm in diameter. The lamp is often fixed within the bottom of your machine. The amount of wood screws should not be much less compared to the amount of the lamps.

3: in accordance to the framework in the base wall lamp wall lamp might be used or no base station base station. With all the base station should really be fixed base station, then the lamp is fixed around the bottom table. The end table is usually created of wood, along with the thickness with the board should be in excess of 15 mm, along with the surface with the paint is painted. Wall lamp set up can use light box set up screw hole into screw to repair the, also could be while in the walls with the drilling, pre buried wood blocks or plastic growth pipe screws to repair. Wall lamp base screw is generally significantly less than two pieces. The set up height of wall, ground 2~2.two meters away from the center on the installation with the basic lighting, wall lamp with 1.two ~1.4 meters is suitable

4: downlight is ideal for embedded lamps, ceiling. Basic form of lamps and lanterns is cylindrical, mouth lamp for plating lead, titanium or nickel plated metal broadside ring, from the lamp installed later on, close to the best surface, great decorative. The lamp tube includes a symmetrical on both sides of the clamping spring device is fixed as downlight. The opening during the lamp opening route, spacing adjustment nut spring by the butterfly. Set up methods:

5 according to size downlight, installation place within the ceiling on scribing and drilling six will the ceiling reserved power supply line with downlight connecting as a result of adjusting the lamp fixed spring leaf butterfly nut, the spring piece along with the height on the ceiling thickness with the identical downlight pushed into the ceiling opening hole, and fitted by using a ideal bulbs